• Fully fabricated hot dip galvanized steel structure.
  
  
• Extra reinforcement to treadle supporter.
  
  
• Six hold down pockets for greater efficiency and stability.
  
  
• Handle lock is provided for comfortable operation.
  
  
• Cast iron pulley for longer trouble frees operation.
  
  
• Good quality, sturdy wire rope for longer life.
  
  
• 1 ½” BSP female coupling for easy dismantling of pump for storing when not in use.
  
  
• 1 ½” BSP female coupling for easy and leak tight joint for water outlet.

1. HANDLE
2. HANDLE LOCK
3. CYLINDER
4. VALVE BOX
5. 1 1/2" BSP FEMALE
   COUPLER
6. HOLD DOWN POCKET
7. PULLEY
8. DISCHARGE PIPE

1. HOLDING PIPE
2. HANDLE
3. PULLEY
4. ROPE
5. TREADLES
6. CYLINDERS
7. VALVE BOX
8. HOLD DOWN
   POCKETS
9. WOODEN BLOCK
10. PISTON ROD
11. 1 1/2" SOCKET

• Piston rod is made of 12 mm Dia steel rod and provided with 8 mm Dia hook loop and threaded connection for easy assembly and is hot dip galvanized.
  
  
• Abrasion and water-resistant piston seal for efficient and longer pumping life.
  
  
• Piston disc and Intermediate washer is provided for smooth movement of piston.
  
  

• 110 mm Dia x 340 mm long x 3-mm thick seamless cylinder body with smooth internal surface for maximum out put with minimum efforts.
  
  
• Strategically ventilated valve plate to comply with cylinders efficiency.
  
  
• Abrasion and water-resistant rubber valve flap for longer operational life.
  
  
• 10 mm square valve retainer for holding valve flap and protecting the valve plate from operational impact.

1. M12 nut
2. PISTON DISC
3. PISTON SEAL
4. INTERMEDIATE WASHER
5. PISTON SEAL
6. PISTON DISC
7. PISTON ROD
8. LOOP
9. WASHER

1. PISTON ROD
2. M12 NUT
3. PISTON SEAL
4. M12 NUT & WASHERS
5. INTAKE VALVE
6. INLET
7. WOODEN BASE BOARD
8. PISTON DISC
9. INTERMEDIATE WASHER
10. CYLINDER
11. M6 X 35 BOLT WITH NUT
12. 10 MM SQUARE
13. VALVE RETAINER OUTLET
14. M8 X 75 BOLT WITH NUT & WASHER
15. DISCHARGE VALVE

1. VALVE RETAINER
2. DISCHARGE VALVE FLAP (BELOW VALVE PLATE)
3. OUTLET
4. VALVE BOX HOLD DOWN POCKET
5. INTAKE VALVE FLAP (SHADED ABOVE VALVE PLATE)
6. PLAN VIEW AFTER FLAP VALVA FITTING
7. INLET

• Treadle support with extra flat brazing to give maximum ease to the operator while operating with longer treadles.
  
  
• Base Frame is in Wooden and MS.
  
  
• Treadle foot rest supports the rear of pump for stability.
  
  
• 1 ½” NB x 900 mm long inlet pipe provided with threading and lock nut at one end for easy mounting and dismantling.
  
  
• 1 ½” BSP coupling to take elbow or bend connection to inlet pipe.
  
  

1. HANDLE
2. WOODEN TREADLES
3. TREADLE SUPPORT
4. INLET PIPE SOCKET
5. PULLEY
6. WIRE ROPE
7. DISCHARGE PIPE SOCKET
8. WOODEN BASE BOARD
9. HANDLE LOCK
10. CYLINDER
11. VALVE BOX
12. REINFORCEMENT
13. INLET PIPE SOCKET

TOP